Fujitsu Flash Mcu Programmer Download
Feb 9, 2019 - FUJITSU FLASH MCU Programmer for FR (Flash.exe). Shablon v vorde ramka so shtampom gorizontaljnij a4 2016. The FUJITSU FLASH MCU Programmer FR (FME) is freeware tool to programm Fujitsu.
1 FUJITSU FLASH MCU Programmer for F 2 MC-16LX Specifications 2 FUJITSU FLASH MCU Programmer for F 2 MC-16LX Specifications Version September 2008 Software version: V01L FUJITSU LIMITED Printed in Japan 1. Circuit diagrams utilizing Fujitsu products are included as a mean of illustrating typical semiconductor applications. Complete information sufficient for construction proposes is not necessarily given. Psp homebrew app store download software.
The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies.
The information contained in this document does not convey any license under the copy right, patent right to trademarks claimed and owned by Fujitsu. Fujitsu reserved the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu. The products described in this document are not intended for use in equipment requiring high reliability, such as marine relays and medical life-support systems. For such applications, contact your Fujitsu sales representative.
If the products and technologies described in this document are controlled by the Foreign Exchange and Foreign Trade Control Act established in Japan, their export is subject to prior approval based on the said act. 19 (c) Select the COM port of the PC connected to the user system. Click the [Set Environment] button in the main dialog box to open the setup window. When the [COM PORT] tab in the setup window is clicked, the specifying window is opened. Select any of the following COM ports. COM1, COM2, COM3, COM4, COM5, COM6, COM7, COM8,COM9,COM10 COM11, COM12, COM13, COM14, COM15, COM16, COM17, COM18,COM19,COM20 (d) Execution of downloading Click the [Download] button.
If the following dialog window is opened, Input a reset signal to the microcontroller to start the program in the flash programming mode and then click the [OK] button Downloading is performed to open the Download window. When downloading is completed normally, the following dialog window opens.
When the [OK] button is clicked to close the dialog window, the [Erase], [Blank Check], [Program & Verify], [Read & Compare] and [Copy] buttons are enabled. Note: Downloading can also be performed using the Tab key to move to the [Download] button and pressing the Enter key or pressing the ALT and D keys at the same time. 13 20 7.2 Erasing and Programming This section explains how to specify Hex File and the processing and operation performed when the [Erase], [Blank Check], [Program & Verify], [Read & Compare], [Copy] and [Full Operation (D+E+B+P)] buttons are clicked. Each execution can also be performed by pressing the key corresponding to the underlined character in the button name while pressing the ALT key. (Hex File is a O character in Open button, click the ALT + O keys). (a) Hex File: Select the file to be programmed to flash memory Specify the Motorola-S or Intel-HEX format file to be programmed to flash memory in the microcontroller.
Although the specification method by drags and drops a direct file from Explorer etc. Is recommended, it can specify also by the file appointed window displayed by pushing the [Open] button. Hex File must be specified to execute [Program & Verify], [Read & Compare] and [Full Operation (D+E+B+P)]. Since it is decoded at the head of these processings each time, even if the specified Motorola S or Intel-HEX format file changes specification of a file just before processing, it is OK. (b) Erase: Erase all flash memory areas All flash memory must be in the erase state (0xff) when programming a new program to it.